My friends have a 2000 Ford Taurus. They have not had heat for a while now. They have changed the thermostat, flushed the heater core and they know that everything is going through the heater core properly. I have the suspicion that the temperature control door inside the heater/air-conditioning box is stuck to the A/C setting. Does anyone know how to manually adjust this to make it be on the heat setting?No heat in a 2000 Ford Taurus. Possibly the control door in the heater/air conditioning box?I'm not sure where it's located on your car but I know you will have to go in and prop it open or closed with something, preferably something like a gum consistency. When you do that though they will only be able to have heat. Then in the summer you can switch it and it will only have air. But will work until you save up for it, its about $700 to fix. Fords, I think, are notorious for this problemNo heat in a 2000 Ford Taurus. Possibly the control door in the heater/air conditioning box?Your thinking is right, they have a tsb out for a blend door sticking and it's an not an easy job, sometimes you can sneak your hand up there and move it by hand, the prob is the door warps and sticks in the passage to hard for the arm to move it. Usually not to hard for a hand though... Good luckNo heat in a 2000 Ford Taurus. Possibly the control door in the heater/air conditioning box?Open the glove box and squeeze the sides inward and remove.then you can get to the blend door.
Check this those blend/diverter doors malfunction a lot.
http://cgi.ebay.com/ebaymotors/Ford-Taur
Thursday, June 2, 2011
Heater core on a 1999 durango?
I have a 1999 dodge durango and smell antifreeze when the heater is on, but Im not loosing any antifreeze in the overflow tank or the radiator. And if it is the heater core, how hard is it to change. I know some cars you have to take out the dash. anyone here changed one?Heater core on a 1999 durango?I work for a Chrysler dealer in service. It sounds like a heater core. If you can smell it and don't see any leaks on the ground, it more than likely is the core. If it starts to leak on the pass side floor inside the vehicle or you get a mist out of the vents when the heater is on, then that is the tell tale sign that the heater core is shot. Yes, you do have to pull the dash to change it. It's about a 4-5 hour process for our techs.Heater core on a 1999 durango?Just get obama to get you a new truck on the tax payers.Heater core on a 1999 durango?IT TAKES 5 HOURS TO DO IT WHICH INVOLVE REMOVING THE DASHBOARD. ANY TIME YOU SMELL ANTIFREEZE WHICH IS BAD FOR YOUR HEALTH, THE HEATER CORE IS LEAKING COOLANT. THE REASON WHY YOU NOT LOOSING COOLANT IS IT IS LEAKING VERY SMALL ENOUGH TO SMELL IT.Heater core on a 1999 durango?If your heater core is leaking, you'll have coolant leaking inside your car and eventually lose coolant. Are you sure it is antifreeze you smell or more like mildew or musky smell which indicates build up in your heater core. I'm not familair with your vehicle but in some, you can get to it from the firewall inside the engine housing.
How much does it cost to replace a heater core?
I have a 1995 Ford Contour GL, 2.0 that I believe needs a heater core. I don't have time right now to replace it, so I am wondering about how much it would cost for parts and labor for the replacement. The dash does not need to be taken out, however the center console and shifter assembly does (without tearing apart wires and effing the overdrive). Other than that it's just a matter of removing some things and changing it out. Thanks in advance for your responses!How much does it cost to replace a heater core?I don't know the specific time for it but if that's all your saying needs to be taken out then maybe 2 or 3 hours labor and then parts cost so possibly $200-400 in that range. How do you know it's leaking? Coolant on the floor? If you don't have the money it can be bypassed since you won't be using it much in the warmer season.
How to Bypass 1997 Jeep Grand Cherokee Heater Core?
The heater core is leaking on the passenger side of the cabin. How hard is it to do a bypass? How is is it done? Step-by step method. I am a change oil and filter guy and not a mechanic.
The radiator shop wants $500 to replace the heater core. I would like to keep the Jeep for pulling a pop-up camper.How to Bypass 1997 Jeep Grand Cherokee Heater Core?Well, 500 bucks to change the heater core is not too bad, considering the entire dashboard has to be removed to get to it.
Anyhow, it's real simple to bypass the heater. You can't block the flow - it has to always be circulating. Just cut the 2 hoses entering and exiting the firewall with a utility knife and connect them together with a coupler and clamps.
Before you bypass the heater, check that the problem isn't with one of those connections at the firewall. I had leaking antifreeze coming into the passenger side and the shop told me the core was bad and wanted 700-800 to replace it. I decided to do it myself. Bought a core for 79.00. Then started taking things apart. I noticed that one of the hose clamps was loose and was squirting water into the core when the engine ran. Put a new clamp on it and no more leak!
The radiator shop wants $500 to replace the heater core. I would like to keep the Jeep for pulling a pop-up camper.How to Bypass 1997 Jeep Grand Cherokee Heater Core?Well, 500 bucks to change the heater core is not too bad, considering the entire dashboard has to be removed to get to it.
Anyhow, it's real simple to bypass the heater. You can't block the flow - it has to always be circulating. Just cut the 2 hoses entering and exiting the firewall with a utility knife and connect them together with a coupler and clamps.
Before you bypass the heater, check that the problem isn't with one of those connections at the firewall. I had leaking antifreeze coming into the passenger side and the shop told me the core was bad and wanted 700-800 to replace it. I decided to do it myself. Bought a core for 79.00. Then started taking things apart. I noticed that one of the hose clamps was loose and was squirting water into the core when the engine ran. Put a new clamp on it and no more leak!
I need step by step instructions and a diagram on 2000 dodge derango?
I need to know how to change the heater core on this I have changed alot of these but not on this model and i hear its alot different so if anyone knows where I can find a place on the web to see please let me know thanksI need step by step instructions and a diagram on 2000 dodge derango?Chilton's. Here's a link:http://www.chiltondiy.com/default.aspx
The books have been my main reference source for many years.I need step by step instructions and a diagram on 2000 dodge derango?pet-boys should have the book on that model. you might want to call the store before you go, make sure the book is in the store. you could also check out the dodge website they could have a manual online you could check out or you could order a copyI need step by step instructions and a diagram on 2000 dodge derango?Here is step-by-step instructions and an illustration for replacing the heater core on a 1999 Dodge Durango and Ram and I expect it will be the same for the 2000 model.
http://www.2carpros.com/forum/1999-dodgehair designs Homemade Duvet Cover
The books have been my main reference source for many years.I need step by step instructions and a diagram on 2000 dodge derango?pet-boys should have the book on that model. you might want to call the store before you go, make sure the book is in the store. you could also check out the dodge website they could have a manual online you could check out or you could order a copyI need step by step instructions and a diagram on 2000 dodge derango?Here is step-by-step instructions and an illustration for replacing the heater core on a 1999 Dodge Durango and Ram and I expect it will be the same for the 2000 model.
http://www.2carpros.com/forum/1999-dodge
How do I remove and reinstall heater core in my 2000 chevy blazer?
I have removed the dash board but can not seem to find bolts for firewall side removal. I have a 2000 chevy blazer two wheel drive. My heater core is bad and I need to change it but I'm having trouble getting it out please help.How do I remove and reinstall heater core in my 2000 chevy blazer?There are none on the firewall side. You have to kind of just do it blind. 1/4 inch drive with swivel and extension. I think they are 7mm. Sorry, I know that's a real *****. Good luck.
Is the inlet hose the top or bottom hose on the firewall ?
I have a 93 isuzu rodeo I got it about 2 months ago there was no heater hoses to the heater core . changed the heater core with new one but I do not know what hose to place where .the heater core pipe from fire wall are top and bottom how does the hoses go one top of heater core to botton of moter someone help me .Is the inlet hose the top or bottom hose on the firewall ?ha ha ive heard it dosent matter but it does matter just hook them up ,and if you hear a gurgeling coming from under the dash that means they are backwards air will get traped in the heater core and gurgle if it gurgles you have the charge hose on the bottom ..it wont hurt anything ,,,it just forces the air out when you start it ...Is the inlet hose the top or bottom hose on the firewall ?It won't matter at all.
How much to fix a heater core?
I have a Ford Tarus 99 how much would it be to fix a heater core??? Plus if we have changed thermostat, flushed ratiator and heater still don't work it the heater core definatly the problem????How much to fix a heater core?Ok a few questions for you. Does the blower blow air? And did all the air get out of the system? If it didn't it could be causing a air pocket that won't let the fluid flow. but if all of that is good then it really shouldn't cost that much depending on where you liveHow much to fix a heater core?When you had done all of the items. When you where running the car did you turn on the heater? It will take some time for the new fluids to make its way back into the core. Start car and turn on the heater. Open radiator cap first to get a good flow. Warm up car. Check after about 10 min. to see if you have good flow in radiator. When there is a good flow. Then check to see if you have heat. Replace radiator cap. Then recheck heater. If not working still, Then check for a collapsed heater feed line hose.How much to fix a heater core?The labor time needed to make a heater core repair is 5 hours per ALLDATA. The factory heater core is $74.00, so this is not a really quick or cheap repair. I'm guessing from what you have done so far on the vehicle that you are having overheating problems. The only thing that really happens to heater cores is they begin leaking when they get older. If you are having overheating problems....the first thing to check (since you have replaced the thermostat) would be to make sure the electric fan is kicking on like it is supposed to....these are controlled with by a module and I believe they operate at 2 different speeds. I hope this helps.
My heater in my truck wont work help.?
I have the thermostat as high it will go and cold air comes out. I just had my fluid flushed by some jackass and since then my a/c quit and now my heater wont work.What might the problem be? Heater core? I already checked all of my fuses.1999 GMC Envoy how hard is it to change the heater core if thats the problem?My heater in my truck wont work help.?Well if it started after the guy did a tap dance all under your hood you need to take it back to him. Get him to fix it.My heater in my truck wont work help.?You could have a air lock from the fluid flush. But the heater core should be fine. Did they replace the thermostat when they flushed the fluids?My heater in my truck wont work help.?fluid flushed and no ac...i once had tune up and got a flat tire...there is a door under dash to direct hot air...it may b stuck closed...ac is compleatly differnt matter unless dash switch is shot.My heater in my truck wont work help.?you should turn the heater on high,then open hood and check both hoses going to heater core, both should be hot. If not then you have a heater core stopped up or a bad water control valve. If both are hot then there is probably a problem with the vac *** control ed air blend system which controls the amount of cool air mixed with heater warmed air. If your heater core is leaking you will probably have fog on windshield and a smell of glycol.My heater in my truck wont work help.?the heat sensor is bad just go to autozone an replace itMy heater in my truck wont work help.?IF the [small] vacuum hose fell off or was taken off that goes inside the vehicle - U will have that problem. butt the air would
just come out the floor vents. The small hose usually connects @ the intake manifold. IF when U accelerate the vent air changes from the upper vents 2 the floor - then its just a vacuum hose.My heater in my truck wont work help.?the suggestion about checking the hoses is the first place to look since that is the easiest. Next, is to check the vacuum line going to your control head (the part that you move to go from hot to cold) that line comes in from the engine compartment and usually goes into the fire wall where the evaporator core is on the passenger side under the hood. In your situation your blend doors can be controled either electrically or by vacuum. the door you are looking for is behind the radio and control head in the passenger compartment. good luck.
just come out the floor vents. The small hose usually connects @ the intake manifold. IF when U accelerate the vent air changes from the upper vents 2 the floor - then its just a vacuum hose.My heater in my truck wont work help.?the suggestion about checking the hoses is the first place to look since that is the easiest. Next, is to check the vacuum line going to your control head (the part that you move to go from hot to cold) that line comes in from the engine compartment and usually goes into the fire wall where the evaporator core is on the passenger side under the hood. In your situation your blend doors can be controled either electrically or by vacuum. the door you are looking for is behind the radio and control head in the passenger compartment. good luck.
Has anyone changed a heater core in a 95 ford ranger p.u.?
the manual says i have to pull the dash on this model isthis true and if so can anyone give me a clue on how best to go about this. thank youHas anyone changed a heater core in a 95 ford ranger p.u.?yes you need to cut the dash unless your truck is just a beater. In that case you just cut the casing thats behind the heater core replace the core and then two part epoxy the case back together. It turns a all day job into a 2 hour job.www.myspaces hair dryer
Anybody every changed a Heater Core on a 1997 Lexus LX450?
My neighbor needs a heater core replaced on her 1997 LX450. Anybody ever tackled this? I know on some of the Lexus models, you have to go as far as taking out the motor mounts and propping the motor up to get to the heater core that is buried between the motor, tranny, and firewall. Others, I know you have to take out the dash. How bad is the LX450, and what does it involve? I am very mechanically inclined, and would like to help my neighbor, so she doesn't have to pay $1,500 at Lexus. Thanks!Anybody every changed a Heater Core on a 1997 Lexus LX450?I've had the dash out of maybe 10 LX's. (i work at a body shop). Get ready..... The dash pad comes off. You don't have to remove the inner support bar(side to side). Start with the glove box and lower cover. Step by step is hard to explain. I don't have books or help when I pull a dash. The parts are very costly if you brake something. E-mail me please before you start.
TW
TW
Cavalier heater core?
Seriously how hard will it be to change the heater core in my '97 chevy cavalier? How long will it take. I was told it will be over an 8 hr job and was given an estimate of $625.Cavalier heater core?Cavalier heater core is located in the middle of the dash, pretty much in line with the gear shifter and console. They arent hard to do, just awkward to get to. Then heater hoses can be difficult to get to, sometimes you have to jack the car up and access them from underneath.
Call around and get 2 or 3 quotes before you pay out the $625. Cavalier heater core?sounds about right... sucksCavalier heater core?It should only take a skilled professional 1-3 hours. I have never worked on a chevy cavalier but it should be accessible from under the dash on the passengers side.Cavalier heater core? I hate to say this but that sounds about right. You can't just yank the housing down to get it out. Half the bloody dash has to come out. SORRY for your loss. This is why people scrap their cars. The repairs start to cost more than the car is worth.Cavalier heater core?Depending on where u go this should range from $150.00-$400.00 I would try a know mechanic that knows his stuff and or small mechanic's shop that would charge u wayyyyyy less.Its hard but not that xpensive.Shops charge by the hour and home based mechs.dont they charge by the job.Cavalier heater core?the part costs 40 dollars at autozone. get another opinion on time. my sisters boyfriend put mine in my sunfire in about 4hrs
Call around and get 2 or 3 quotes before you pay out the $625. Cavalier heater core?sounds about right... sucksCavalier heater core?It should only take a skilled professional 1-3 hours. I have never worked on a chevy cavalier but it should be accessible from under the dash on the passengers side.Cavalier heater core? I hate to say this but that sounds about right. You can't just yank the housing down to get it out. Half the bloody dash has to come out. SORRY for your loss. This is why people scrap their cars. The repairs start to cost more than the car is worth.Cavalier heater core?Depending on where u go this should range from $150.00-$400.00 I would try a know mechanic that knows his stuff and or small mechanic's shop that would charge u wayyyyyy less.Its hard but not that xpensive.Shops charge by the hour and home based mechs.dont they charge by the job.Cavalier heater core?the part costs 40 dollars at autozone. get another opinion on time. my sisters boyfriend put mine in my sunfire in about 4hrs
1997 cavalier heater core?
Seriously how hard will it be to change the heater core in my '97 chevy cavalier? How long will it take. I was told it will be over an 8 hr job and was given an estimate of $625.1997 cavalier heater core?goto Autozone.com and look up the free repair guide for your car. It will tell you how its done.
but my q is: whay do you want to change the heater core??? is it leaking??
If its just a Q of not getting heat-- be advised that the car has a water inlet control valve for the heater core that is located on the water hose going INTO the heater core and it just might be the problem.
A hell of a lot cheaper than replacing a heater core. If the core is not leaking water all over the place that just might be the problem.
but my q is: whay do you want to change the heater core??? is it leaking??
If its just a Q of not getting heat-- be advised that the car has a water inlet control valve for the heater core that is located on the water hose going INTO the heater core and it just might be the problem.
A hell of a lot cheaper than replacing a heater core. If the core is not leaking water all over the place that just might be the problem.
Heater core in Chevy Tracker?
Does anyone know how big a job it is to change a heater core in a 2000 Chevy Tracker? I was told by a local garage the heater core itself was only available from Chevy and cost $300! Does this sound right? Thanks.Heater core in Chevy Tracker?Changing the heater core on a '00 Tracker is moderately difficult. To do it right you must remove the entire dash pan (just like a Ford), but besides that it's easy. The problem with removing the dash pan is the you will probably never get all the rattling out after you reinstall in. As far as getting the core you local parts store should be able to get it for you. You can go to www.advanceautoparts.com or www.autozone.com and check on-line to make sure. If they can get it and you don't mind using used parts go to www.junkyarddog.com (it will link you national salvage yards) good luck.Heater core in Chevy Tracker?contact buy-oem-parts for the best price on the part
Does anyone know how to change out a heater core in a 1999 chevy blazer?
i have a 1999 chevy blazer. my heater core went out the other day. i called to find out how much it would cost to replace it. it was so damn expensive i just bypassed it so now i have no heat. i was told that i would have to take tho whole dash out to fix it. is this true? do you think this is something that a person with no experience can do?Does anyone know how to change out a heater core in a 1999 chevy blazer?if your not experienced it wouldnt be worth your while to takle it the dashboard does need to come forward the steering column dropped down,stereo,ac/ controls,removedDoes anyone know how to change out a heater core in a 1999 chevy blazer?What happened to it? Did it start leaking antifreeze into the interior? How do you know it's the heater core and not the %26quot;Vent blender door%26quot; or some other problem causing the %26quot;no heat%26quot; problem?
You should get a second opinion first.documents into nails painted right
You should get a second opinion first.
How do u change flush a heater core?
In a 1999 ford Taurus, 3.0 L engine, not the doh engine, just the regular 3.0 engine, the coolent does have a brownish tint to it. I've had radiator flushes every single year, but i still have no heat. i heard that flushing the heater core is different, so I'd like to know, step by step in how to do this correctly. My thermostat was changed yesterday, I've touched the pipes in the firewall(was told these are the heater core hoses) and one was warm(luke) and the other was warmer(more than luke), but i still have no heat, my heat blows like luke warm to cold, and it takes a long time to get up there. Help please!How do u change flush a heater core?When you flush the system it runs through the heater core if it isn't heating up correctly try putting a thermostat in that runs a little hotter. I had to do this with a vehicle I owned as it wouldn't blow out hot air it was luke warmHow do u change flush a heater core?You can buy a kit from Canadian tire or Auto Zone for about $7.00 and all you do is hook a garden hose on it start the car then turn on the water. Also you should add a winter thermastat. This will allow the antifreeze to warm up more before it gets cooled off in the rad. If this still doesn't work then put a piece of cardboard in front of your rad.How do u change flush a heater core?flush and drain cooling system.
there is a chemical called C.L.R. you can buy it in most any hardware store. buy 2 lengths of heater hose long enough to reach the heater core and come out the hood enough to get a funnel in one of them, run the other into a bucket under the car. pour the CLR into the funnel and let it run through the heater core. follow with distilled water. reconnect heater lines from motor. refill cooling system with proper mixture of antifreeze and distilled water.
this doesnt always work (about 50% of the time) but its easier and cheaper than a heater core replacement. especially in a taurus.How do u change flush a heater core?IF YOU HAD THE DONE ON A REGULAR BASIS THEN THE HEATER CORE WOULD HAVE BEEN FLUSHED OUT AT THE SAME TIME.
IF YOU WANT TO TRY IT YOURSELF JUST REMOVE BOTH HEATER LINES FROM THE HEATER CORE AND FLUSH IT OUT WITH YOUR GARDEN HOSE.How do u change flush a heater core?you have a valve that control the flow for the heater core,some are controlled by a vacuum or cable when you select heater or the temperature, check the vacuum system for leaks,.because when the controls are working fine the water in the heater core should flow freely heating up the core.I hope this help.
there is a chemical called C.L.R. you can buy it in most any hardware store. buy 2 lengths of heater hose long enough to reach the heater core and come out the hood enough to get a funnel in one of them, run the other into a bucket under the car. pour the CLR into the funnel and let it run through the heater core. follow with distilled water. reconnect heater lines from motor. refill cooling system with proper mixture of antifreeze and distilled water.
this doesnt always work (about 50% of the time) but its easier and cheaper than a heater core replacement. especially in a taurus.How do u change flush a heater core?IF YOU HAD THE DONE ON A REGULAR BASIS THEN THE HEATER CORE WOULD HAVE BEEN FLUSHED OUT AT THE SAME TIME.
IF YOU WANT TO TRY IT YOURSELF JUST REMOVE BOTH HEATER LINES FROM THE HEATER CORE AND FLUSH IT OUT WITH YOUR GARDEN HOSE.How do u change flush a heater core?you have a valve that control the flow for the heater core,some are controlled by a vacuum or cable when you select heater or the temperature, check the vacuum system for leaks,.because when the controls are working fine the water in the heater core should flow freely heating up the core.I hope this help.
1989 Chevy Corsica V6 Heater Core?
Where and how do i change th heater core .. My heat and A/c doesnt work well A/c never worked heater did when i first got car..I already got put in a temp thingy and heater still doesnt work not to worried about A/c but would be nice if it did work :) every once in awhile i smell a hint of radatitor fluid on passengers side ..1989 Chevy Corsica V6 Heater Core?If the heater core isn't leaking, it isn't bad.
You may have a problem with the flapper doors in the ducting. This car may have a valve to control the water going thru the heater core as well.1989 Chevy Corsica V6 Heater Core?u need to be on pimp my ride or somethin, but for real, go to a chop shop1989 Chevy Corsica V6 Heater Core?well,if the core is on the pass side then replace.if on drivers side-ouch!-trade it in.1989 Chevy Corsica V6 Heater Core?That's a tough chore, you have to just about remove your dashboard from the car to get to the thing. First thing you'll need is a haynes or chilton's manual. then remove the bolts securing the dasto the firewall on the passenger side of the car, next drop the duct work in front of the heater core, then drain the radiator fluid from the car. remove the lines from the heater core at the fire wall, remove the core, replace, reconnect the lines, refill the radiator, replace the duct work, and reinstall the dash, make sure you don't break any wires or lines connecting the duct controls. Sounds easy right? Good Luck. A shop will usually charge around $250- $400 It will take you a solid day, you will cuss a lot, and God himself will turn his back on yo for weeks becuse of the things you will say about him. If you or some one you know is hndy you can try this. Go to an auto parts store and buy a tube of radiator stop leak, (wait for the good part) you will also need a drill operated fluid transfer pump, a cheap one is about $20 bucks, some hose that is the same size as the in and out on your core, and some HOT water. Hook the bottom line to your core, and to the pump on the drill, take the HOT water mixed with stop leak and pour it into the hose hooked to the core, put it on the pump. Turn the drill on and circulate it for as long as you care to or until no water leaks from the core (you may burn up the drill) Then flush it with clean water and reconnect the system. I say do this the hard way because I don't advocate putting metal flakes into your cars coolings system, which could potentially foul up something that isn't a problem now, It might cost $75 but could save you $300.
You may have a problem with the flapper doors in the ducting. This car may have a valve to control the water going thru the heater core as well.1989 Chevy Corsica V6 Heater Core?u need to be on pimp my ride or somethin, but for real, go to a chop shop1989 Chevy Corsica V6 Heater Core?well,if the core is on the pass side then replace.if on drivers side-ouch!-trade it in.1989 Chevy Corsica V6 Heater Core?That's a tough chore, you have to just about remove your dashboard from the car to get to the thing. First thing you'll need is a haynes or chilton's manual. then remove the bolts securing the dasto the firewall on the passenger side of the car, next drop the duct work in front of the heater core, then drain the radiator fluid from the car. remove the lines from the heater core at the fire wall, remove the core, replace, reconnect the lines, refill the radiator, replace the duct work, and reinstall the dash, make sure you don't break any wires or lines connecting the duct controls. Sounds easy right? Good Luck. A shop will usually charge around $250- $400 It will take you a solid day, you will cuss a lot, and God himself will turn his back on yo for weeks becuse of the things you will say about him. If you or some one you know is hndy you can try this. Go to an auto parts store and buy a tube of radiator stop leak, (wait for the good part) you will also need a drill operated fluid transfer pump, a cheap one is about $20 bucks, some hose that is the same size as the in and out on your core, and some HOT water. Hook the bottom line to your core, and to the pump on the drill, take the HOT water mixed with stop leak and pour it into the hose hooked to the core, put it on the pump. Turn the drill on and circulate it for as long as you care to or until no water leaks from the core (you may burn up the drill) Then flush it with clean water and reconnect the system. I say do this the hard way because I don't advocate putting metal flakes into your cars coolings system, which could potentially foul up something that isn't a problem now, It might cost $75 but could save you $300.
Need help on removing heater core?
just bought a 1988 ford mustang GT 5.0,The heater core went out.How hard is it to change the heater core in this mustang? I never changed one in a ford product.Thank you!!Need help on removing heater core?The heater core is located behind the glove compartment.
You will need to remove the two heater hoses that enter the
firewall on the passenger's side. They are right next to each
other. Now, remove the glove compartment. The heater core
is behind it. Remove the bracket holding the core. Now,
remove the heater core. Installation is the reverse. Make
sure you have the heater core top side up. This job should
take you approx. 40 minutes.Need help on removing heater core?Check manuals to see how much stuff you have to take out to get to it. You can check under the dash board, usually on the right side. To make this easier, take out:
right side seat
glove compartment drawer and cover
center console
Under the hood, go to the firewall. Disconnect the two heater hoses that pass through the firewall to the heater core.Need help on removing heater core?i think you have to drop the heater box.its more time consuming then hard.
You will need to remove the two heater hoses that enter the
firewall on the passenger's side. They are right next to each
other. Now, remove the glove compartment. The heater core
is behind it. Remove the bracket holding the core. Now,
remove the heater core. Installation is the reverse. Make
sure you have the heater core top side up. This job should
take you approx. 40 minutes.Need help on removing heater core?Check manuals to see how much stuff you have to take out to get to it. You can check under the dash board, usually on the right side. To make this easier, take out:
right side seat
glove compartment drawer and cover
center console
Under the hood, go to the firewall. Disconnect the two heater hoses that pass through the firewall to the heater core.Need help on removing heater core?i think you have to drop the heater box.its more time consuming then hard.
How to change out a heater core on 2001 windstar lx?
Heater Core
Removal and Installation Procedure for 2001 Windstar.
Drain the cooling system.
Remove the cowl top vent panel. Disconnect the heater hoses.
Remove the lower instrument panel utility compartment.
Remove the ash receptacle.
Remove the rear seat airflow duct.
Remove the pins.
Remove the duct.
Remove the four instrument panel support bolts and detach the electrical connectors.
Remove the nuts and remove the center instrument panel support bracket.
Remove the bolts and remove the support brace.
Remove the 2 screws and remove the floor duct.
Remove the 7 cover screws and remove the cover.
Remove the dash panel seal.
Remove the core.
To install, reverse the removal procedure.How to change out a heater core on 2001 windstar lx?check out ford .com about 2001 windstar lx and see that come up
Removal and Installation Procedure for 2001 Windstar.
Drain the cooling system.
Remove the cowl top vent panel. Disconnect the heater hoses.
Remove the lower instrument panel utility compartment.
Remove the ash receptacle.
Remove the rear seat airflow duct.
Remove the pins.
Remove the duct.
Remove the four instrument panel support bolts and detach the electrical connectors.
Remove the nuts and remove the center instrument panel support bracket.
Remove the bolts and remove the support brace.
Remove the 2 screws and remove the floor duct.
Remove the 7 cover screws and remove the cover.
Remove the dash panel seal.
Remove the core.
To install, reverse the removal procedure.How to change out a heater core on 2001 windstar lx?check out ford .com about 2001 windstar lx and see that come up
Changing nova heater core 1970?
Anyone have any tips or steps on how to change the heater core on a non a/c 1970 bbc nova. Going to do it tommorow and have heard a lot of ways you can. any tips let me knowChanging nova heater core 1970?never done a nova, but i am sure they are like any other Chevy, two hoses, a cable and about 10 screws holding it to the firewall. don;t have to drain the colling system, just undo your hoses and tie them up so they don't; drain, drain as much coolant out of the core as you can, if you have it, use air to blow it out, then unbolt it, i don't; know if it goes to the inside to come out, or if you can take it out through the engine compartment.girl tell you she likes you email host
94 jetta VW 5speed heater core location?
I need to change my heater core and do not know if it is by the driverside floor or if it is in the dash. I had been told in a 94 it can be located in either spot, how do I know where. I cannot find anything online.94 jetta VW 5speed heater core location?It's a major chore that requires removing the dash.LOOSE THE EVAPORATOR FROM THE ENGINE COMPARTMENT AND TAKE OF THE COVER ON THE RIGTH SIDE UNDERNEAT THE BLOWER AND THE COVER FOR THE GAS PEDAL, LOOSE THE NUTS THAT HOLD THE WHOLE PLASTIC SHROUDS
PULL IT AND TAKE THE CLIPS OFF THAT HOLD THE HEATER
AND EVAPORATOR TOGETHER THEN YOU GONNA HAVE TO PULL THE PANEL SO YOU CAN GET THE BLOWER COMPARTMENT DOWN A LITTLE BIT, ENOUGH TO PLAY WITH THE HEATER CORE COMPARTMENT,UNSCREW THE BOTTOM BOLT ON THE HEATER PANEL TO GET MORE SPACE AND FINALY TURN IT AROUND JUST ENOUGH TO PULL IT UP JUST THE HEATER CORE AND THERE YOU GO.
Hope this helped94 jetta VW 5speed heater core location?heater core located in the center of the dash.its in the fresh air heater box.
PULL IT AND TAKE THE CLIPS OFF THAT HOLD THE HEATER
AND EVAPORATOR TOGETHER THEN YOU GONNA HAVE TO PULL THE PANEL SO YOU CAN GET THE BLOWER COMPARTMENT DOWN A LITTLE BIT, ENOUGH TO PLAY WITH THE HEATER CORE COMPARTMENT,UNSCREW THE BOTTOM BOLT ON THE HEATER PANEL TO GET MORE SPACE AND FINALY TURN IT AROUND JUST ENOUGH TO PULL IT UP JUST THE HEATER CORE AND THERE YOU GO.
Hope this helped94 jetta VW 5speed heater core location?heater core located in the center of the dash.its in the fresh air heater box.
I'm changing the heater core in a 1994 Ford ranger 4x4. Can someone tell me how to do it & is it hard to do?
Now its been a while, but I believe you go under the dash on the passenger side. There will be some plastic retainers holding the formed kick guard in place, pull those out. When you get down to the plastic area, there should be 4 screws or bolts holding it on, remove those and pull the plastic piece away. Don't forget to drain the coolant system first.
Now, under the hood, find the feed and return line from the heater core and remove them from the heater core. The core should now prettry easily pull back and then down out from under the dash. Place new heater core in, re atttach hoses in engine compartment, replace plastic piece under heater core, and put the formed kick guard back on. Now refill the system with coolant and test out your new heater core.I'm changing the heater core in a 1994 Ford ranger 4x4. Can someone tell me how to do it %26amp; is it hard to do?lamarin is right, check the following web site: http://www.autozone.com/az/cds/en_us/090 ...Good Luck...
And it's a piece of cake. About an hour if you're not in a hurry!!
Now, under the hood, find the feed and return line from the heater core and remove them from the heater core. The core should now prettry easily pull back and then down out from under the dash. Place new heater core in, re atttach hoses in engine compartment, replace plastic piece under heater core, and put the formed kick guard back on. Now refill the system with coolant and test out your new heater core.I'm changing the heater core in a 1994 Ford ranger 4x4. Can someone tell me how to do it %26amp; is it hard to do?lamarin is right, check the following web site: http://www.autozone.com/az/cds/en_us/090 ...Good Luck...
And it's a piece of cake. About an hour if you're not in a hurry!!
When changing a heater core in a 2000 GMC Jimmy, do you have to disconnect airbags and if so how do you do it?
STOP---do not attempt this yourself---if you think the air bags are hooked up to the heater--you obviously do NOT know enough to do this complicated dirty job. Let a shop do right.When changing a heater core in a 2000 GMC Jimmy, do you have to disconnect airbags and if so how do you do it?I attempted it myself. Not a problem. Not that complicated or dirty. Nothing was damaged. Heater works great. Saved myself about $800.00.
ttemple
your dealing with an explosive device and SERIUOS if not FATAL injuries could occur
i have blown one airbag on a 1998 Camaro it wasn't pretty and it did hurt like hell and the thing about it was i KNOW what i'm doing
i had to replace the
passanger airbag 300.00
the windshield = 300.00 used and installed
the Dash 700.00 plus color matching
the Derm(diagnostic energy reserve module) 200.00
so DON'T try this at homeWhen changing a heater core in a 2000 GMC Jimmy, do you have to disconnect airbags and if so how do you do it?I AGREE WITH THE OTHER TWO ANSWERS. YOU SHOULD NOT TRY THIS YOURSELF.
ttemple
Report Abuse
When changing a heater core in a 2000 GMC Jimmy, do you have to disconnect airbags and if so how do you do it?STOP this is a repair for the PROFESSIONALS onlyyour dealing with an explosive device and SERIUOS if not FATAL injuries could occur
i have blown one airbag on a 1998 Camaro it wasn't pretty and it did hurt like hell and the thing about it was i KNOW what i'm doing
i had to replace the
passanger airbag 300.00
the windshield = 300.00 used and installed
the Dash 700.00 plus color matching
the Derm(diagnostic energy reserve module) 200.00
so DON'T try this at homeWhen changing a heater core in a 2000 GMC Jimmy, do you have to disconnect airbags and if so how do you do it?I AGREE WITH THE OTHER TWO ANSWERS. YOU SHOULD NOT TRY THIS YOURSELF.
Can anyone tell me how to go about changing a heater core in a 1985 Ltd crown victoria?
You should be able to remove your glove box,there should be a cover for the heater core,youll also need to diconect the two heater hoses in the engine compatrment going thru the firewall.Can anyone tell me how to go about changing a heater core in a 1985 Ltd crown victoria?its not coming out the glove box have the towncar which is the same car basically you gotta drop the dashboard, go to www.lincolnonlineforum.com it will give you step by step instuctions look in the tech sectionCan anyone tell me how to go about changing a heater core in a 1985 Ltd crown victoria?Not for the weak of heart.The entire dash must come out then the heater box.Best left to pros.
How to change out the heater core on a 1994 Chevy Blazer?
Changing the core should not be attempted by anyone. You have to remove your dash as well as work under the hood. Most mechanics try everything to keep from replacing the core. Anyways, once you have dash torn apart, (your core will resemble your radiator) drain out as much fluids as possible, disconnect the hoses under the hood and then begin the dismounting unit. Reverse the procedure for replacement.
If your heater is simply not producing heat in the cab, try flushing your system and replacing the engine thermostat.How to change out the heater core on a 1994 Chevy Blazer?Its way to complicated to explain here,go to the parts store and pick up a chiltons or haynes manual.This manual will give you all the info you need to do any job including rebuilding the engine if you need to and they are fairly cheap.Good luck.How to change out the heater core on a 1994 Chevy Blazer?Ok im doing mine right now to, buy the book first, then you need to pull out the glove box, ash tray, and disconnect all the cables leading to the heater box under the dash, then you get into the motor compartment and where the heater and air conditioner is you should find maybe 3 nuts that are around the air conditioner or the heater box, don't touch the bolts, one might be a ***** because of the inner fender, and you might need to lower that to get to it, then grab the heater box from the inside and lift and pull it out,
open it up and change out the heater core, then back together, I tried to make it sound easy but it really sucks.find cheap duvet covers hair highlights
If your heater is simply not producing heat in the cab, try flushing your system and replacing the engine thermostat.How to change out the heater core on a 1994 Chevy Blazer?Its way to complicated to explain here,go to the parts store and pick up a chiltons or haynes manual.This manual will give you all the info you need to do any job including rebuilding the engine if you need to and they are fairly cheap.Good luck.How to change out the heater core on a 1994 Chevy Blazer?Ok im doing mine right now to, buy the book first, then you need to pull out the glove box, ash tray, and disconnect all the cables leading to the heater box under the dash, then you get into the motor compartment and where the heater and air conditioner is you should find maybe 3 nuts that are around the air conditioner or the heater box, don't touch the bolts, one might be a ***** because of the inner fender, and you might need to lower that to get to it, then grab the heater box from the inside and lift and pull it out,
open it up and change out the heater core, then back together, I tried to make it sound easy but it really sucks.
How to change a heater core on a 1994 gmc truck? doe sthe dash have to come out?
any input would be well appreciatedHow to change a heater core on a 1994 gmc truck? doe sthe dash have to come out?Not all the dash but some pieces have to come out. It's under the glove box area. My labor book says 1.5 hours for that job on the %26quot;C%26quot; series (full size GM truck) so it isn't that bad. I'd suggest getting a service manual, like Haynes or Chilton.How to change a heater core on a 1994 gmc truck? doe sthe dash have to come out?I am not sure. Best check out a shop manual to make sure A/C is not a problem.How to change a heater core on a 1994 gmc truck? doe sthe dash have to come out?dash does not have to come out and the prices vary....depends on whos doing the workHow to change a heater core on a 1994 gmc truck? doe sthe dash have to come out?econofix is right . The dash does not have to come out . Compared to most cars this is a very easy job. Remove the lower airbox cover under the dash, located right below the glove box . This part is black in color and has about 10 ? screws in it. Heater core is in there. Remove two heater hoses under the hood
Make sure the engine is cooled off of course.How to change a heater core on a 1994 gmc truck? doe sthe dash have to come out?It's a little easier on those models. The Haynes and Chiltons is primo advice, go that route and follow the directions.
Haynes Manual @ AutoZone $15
New Coolant @ AutoZone $23
1.5 hours of time and knowing you did it yourself and saving $300-$450 PRICELESS. because that's about what it will cost you.
Make sure the engine is cooled off of course.How to change a heater core on a 1994 gmc truck? doe sthe dash have to come out?It's a little easier on those models. The Haynes and Chiltons is primo advice, go that route and follow the directions.
Haynes Manual @ AutoZone $15
New Coolant @ AutoZone $23
1.5 hours of time and knowing you did it yourself and saving $300-$450 PRICELESS. because that's about what it will cost you.
How to change out a heater core in a 1996 Mustang Coupe?
I believe it is similar to the placement in a camaro. To find your heater core, look under your hood for a silver canister with silver lines running into the firewall into the interior. I am betting it is located behind the passenger side glove box. Should be about 3 nuts to remove glove box and use a flashlight to see how to unbolt heater core.How to change out a heater core in a 1996 Mustang Coupe?you make it sound so easy
the silver lines are for the air conditioner and they go to the evaporator.
i think he needs a mechanic, not an internet guesser
lol
please videotape the installation if you do it yourself and post it at youtube, i need a good laugh.
the silver lines are for the air conditioner and they go to the evaporator.
i think he needs a mechanic, not an internet guesser
lol
please videotape the installation if you do it yourself and post it at youtube, i need a good laugh.
Report Abuse
How to change out a heater core in a 1996 Mustang Coupe?If it is leaking coolant it needs changed. If not leaking don't change. Go get a CHILTONS or HAYNES repair manual if you need to change it. Lot of heater cores changed for wrong reasons.1985 GMC pickup needs heater core changed?
Wondering if there was any place on the internet where I can find a free repair manual on how to change the heater core on my 1985 GMC pickup1985 GMC pickup needs heater core changed?yes autozone.com
goodluck1985 GMC pickup needs heater core changed?Why not go ahead and buy the manual (Haynes) from AutoZone , it will cost you less than $20........... you can use it to find out how to repair everything else on truck except the transmission! You only need to remove about 12 screws, and 3-4 bolts, - it is easier than taking our tonsils out through your ear! I have done it in about 1 1/2 hours, you should be able to do it in 3! Actually not that hard, but the bolts and screws are hard to find, - if you don't know where to look!
goodluck1985 GMC pickup needs heater core changed?Why not go ahead and buy the manual (Haynes) from AutoZone , it will cost you less than $20........... you can use it to find out how to repair everything else on truck except the transmission! You only need to remove about 12 screws, and 3-4 bolts, - it is easier than taking our tonsils out through your ear! I have done it in about 1 1/2 hours, you should be able to do it in 3! Actually not that hard, but the bolts and screws are hard to find, - if you don't know where to look!
How to change a heater core out of a 1997f-150?
You have to remove the entire instrument panel, and it is no easy task, a bucket load of screws. It is a 7 hour job with a professional mechanic working on it, I would not recommend it be done at home unless you know what you are doing.How to change a heater core out of a 1997f-150?its behind your glove box. you have to take your glove box out.How to change a heater core out of a 1997f-150?its a chore and if i remember correctly you have to discharge the a.c. system. go to the library and check it out. some of those fords are worth paying someone else to do it, trust me
How to replace a heater core in a 1988 Ford Escort?
i own a 1988 Ford Escort LX and the heater core went out. if any one can help me out with some directions on how to change the heater core in it, it would be very Helpful. i live in Joliet, IL and it is quite cold. or if anyone close by knows how and is intrested PLEASE LET ME KNOW!!! Thanks!How to replace a heater core in a 1988 Ford Escort?i own a repair shop,and there's no heater core that can be changed in a few minutes,you need a good Haynes repair manual on this car,it will guide you through the whole process,on doing this one,there's a lot to changing one on a escort, buy a good manual and read it good,you,ll see what I'm talking about good luck,i hope this help,s.How to replace a heater core in a 1988 Ford Escort?Its probabily located under the dashboard somewhere, thats all I know dude. Ive only changed 1 heater core before, but it was on a Pontiac, but it only took 10-15 mins.How to replace a heater core in a 1988 Ford Escort?If it is anything like my S15 Jimmy 4X4 find a new car!
It was behind the dash like all of them but it took 4 days to change it as you have to remove the entire dash to get to it.
Most heater cores I have changed (About 7) have taken from 20 minutes to 4 hours, this was the worst I have ever had to do, and 4 weeks later a head gasket blew!
Oh well.How to replace a heater core in a 1988 Ford Escort?ur model is quite old n difficult to get its spare parts.u need certain modification of ur heater core.ask the mechanic 4 help.How to replace a heater core in a 1988 Ford Escort?Buy a repair manual, or go to the nearest public library to look at one for free.prom hair bird
It was behind the dash like all of them but it took 4 days to change it as you have to remove the entire dash to get to it.
Most heater cores I have changed (About 7) have taken from 20 minutes to 4 hours, this was the worst I have ever had to do, and 4 weeks later a head gasket blew!
Oh well.How to replace a heater core in a 1988 Ford Escort?ur model is quite old n difficult to get its spare parts.u need certain modification of ur heater core.ask the mechanic 4 help.How to replace a heater core in a 1988 Ford Escort?Buy a repair manual, or go to the nearest public library to look at one for free.
Does some noes how hard to change a heater core on a 1997f150?
I do believe it's behind the glove compartment. If you are decently good with tinkering it should take no more than two hours.Does some noes how hard to change a heater core on a 1997f150?hard is only that one has to lay in odd way to get to screws and like other one said couple hours work to remove everything only tip i can give is grease the hoses really well and dont twist on them to much when push back on an dreplace the hoses while you got it all a part might fine
repair manual type this dont think you will need it not much more than removing a lot of screws really thats the hard part you have to lay side ways or upside down to do it
repair manual 1997 ford f150 PDF
repair manual type this dont think you will need it not much more than removing a lot of screws really thats the hard part you have to lay side ways or upside down to do it
repair manual 1997 ford f150 PDF
How do you change a heater core on a VW Jetta (96).?
Do i have to rip the whole dash off? is there a website that will show me how? HELP!!!!How do you change a heater core on a VW Jetta (96).?You can go on line and look around. Heater cores can be a pain to near impossible. I can't speak for the VW jetta. You may want to price out an independent car shop. Try car talk dot com and look for recommended mechanics. You put your zip in. Call around and get a price. It may be easier and best to get it a shop to do the repair. At least price it out. The part is not cheap either. It is a super common problem and some shops have the practice and can get it done with out issues, but it will not be cheap. Sorry
I have a factory shop manual and found several areas in which no guidance was offered or where information was incomplete.
I wouldn't start this unless you are an above average mechanic and have good tools and better than average patience.
Some manuals are poor and not very complete. If you don't have some experience and ablities it can be tough. I recall you have to remove the dash and if you have AC it will complicate it more. Good luckHow do you change a heater core on a VW Jetta (96).?Go to your local auto parts store and buy a Haynes Manual for your car and it will give you complete instructions with illustrations.
I have a factory shop manual and found several areas in which no guidance was offered or where information was incomplete.
I wouldn't start this unless you are an above average mechanic and have good tools and better than average patience.
Some manuals are poor and not very complete. If you don't have some experience and ablities it can be tough. I recall you have to remove the dash and if you have AC it will complicate it more. Good luckHow do you change a heater core on a VW Jetta (96).?Go to your local auto parts store and buy a Haynes Manual for your car and it will give you complete instructions with illustrations.
How to change a heater core on a 1995 buick regal?
Oh Lord, have you got a lot of work ahead. Just get out the big wallet and take it to the shop. Take a look in Chiltons Auto Repair Manual at the library and you will see if you really want to break your back on that one. I hear them starting up the big money sucking machine, but hold still until it's over and you'll have heat again.How to change a heater core on a 1995 buick regal?That is one of the jobs where the mechanics earn their money. Not fun at all.
How hard is it to change out the heater core in a 2003 PT Cruiser?
Any details would be appreciated as I would like to do this myself.How hard is it to change out the heater core in a 2003 PT Cruiser?its hard to change any parts on a pt cruiser. get a repair manual.
How to change a heater core on a 1993 grand marques?
Frankie is right. Look in Chiltons. Then consider paying a shop to do it. Anybody might take it apart, but you want it to get put back together correctly.How to change a heater core on a 1993 grand marques?Your best bet is to get a repair manual (about $20.00) at your auto parts store. It has step-by-step instuctions on how to do about any repair you need to do. The heater core is usually under the dash on the passenger side and a lot of times you have to remove part of the dash to get to it.
They're not fun so good luckhard contacts in soft hoping for some advice
They're not fun so good luck
How do you change out a Heater Core for a 1992 Chevy APV Van?
Is this able to do without removing the whole dash board? If its even easy I will do it myselfHow do you change out a Heater Core for a 1992 Chevy APV Van?First answer is a good one only i like the haynes book better. also the book states that it is a 1.3 hour job so if you were to do it yourself it would take a little more time than that. good luckHow do you change out a Heater Core for a 1992 Chevy APV Van?That is a tough question to answer......go to autozone and get a copy of Chiltons repair manual for this vehicle...it will tell you how to change the heater core....Chiltons will cover the model and year you have....or have a good mechanic do it.....heater cores are not that expensive, maybe 50-80 dollars.....do you really want to do this job....replacing a h/c is only required once in the lifetime of most vehicles.
How big of a pain is it to change a heater core on a 94 F-150?
you have to take the whole heating system out from under the dash.good luckHow big of a pain is it to change a heater core on a 94 F-150?visit www.motorcraftservice.com and if you like what they tell or show you, go for it.How big of a pain is it to change a heater core on a 94 F-150?the whole dash has to be removed,, I believe.
real pain in the butt.How big of a pain is it to change a heater core on a 94 F-150?It is not all that hard, just time consuming, It not like you pulling the engine or something, you can do it you just need to be patient and devote some time to it. Will save you alot of money if you do it yourselfHow big of a pain is it to change a heater core on a 94 F-150?It's really not that bad. I believe all you have to do is open up theglove compartment and remove the inner glove compartment and maybe one more inner cover and the heater core should be exposed. Then all you have to do is drain about two gallons of anti-freeze and then you can remove the old heater core then you can install the new one. Then fill it back up with anti- freeze. Then put the glove box back together.How big of a pain is it to change a heater core on a 94 F-150?94 takes 2 hrs., remove glove box, then remove heat core housing opening
real pain in the butt.How big of a pain is it to change a heater core on a 94 F-150?It is not all that hard, just time consuming, It not like you pulling the engine or something, you can do it you just need to be patient and devote some time to it. Will save you alot of money if you do it yourselfHow big of a pain is it to change a heater core on a 94 F-150?It's really not that bad. I believe all you have to do is open up theglove compartment and remove the inner glove compartment and maybe one more inner cover and the heater core should be exposed. Then all you have to do is drain about two gallons of anti-freeze and then you can remove the old heater core then you can install the new one. Then fill it back up with anti- freeze. Then put the glove box back together.How big of a pain is it to change a heater core on a 94 F-150?94 takes 2 hrs., remove glove box, then remove heat core housing opening
How to I change the heater core on a 95 eldorado?
Well first let me say this is not a job you a lay men
You must remove the heater core from under the dash. It is not easy and you must in some cases remove the dash itself.How to I change the heater core on a 95 eldorado?VERY CAREFULLY
You must remove the heater core from under the dash. It is not easy and you must in some cases remove the dash itself.How to I change the heater core on a 95 eldorado?VERY CAREFULLY
Details on how to change a heater core....?
In a 1990 Beretta GT with a 3.1 V6 and YES I am sure the heater core is the problem. It has been Bypassed because the previous owners noticed it leaking and decided not to mess with it since at the time in was in the middle of summer....If anyone can give me details OR even send me pics... email me at nativepride76642@yahoo.com if you have illistrations:-) Thanks!!!Details on how to change a heater core....?i own a repair shop,and no one can give you good details on this job,,its too complex,,you,ll have to get a repair manual on this one,,there's too much detail work involved here on this one,,i have done a few of those,,and there a pain to do,,either way you need a good Haynes repair manual ,,for this job,i wouldn't even start this job without one,,good luck i hope this help,s.Details on how to change a heater core....?your welcome.
Report Abuse
Details on how to change a heater core....?Heater cores are a big pain in the butt. Have a shop do it. I had my whole heater box replaced, it contained the heater core, ac evaporator and blower motor, the whole dashboard had to come out of the truck.... there was nothing there but the steering colum anf the firewall, it took the shop 5 days and cost me $1000 for the whole job. It should be a little cheaper for you cuz you are just changing the core, I would say around $500.Details on how to change a heater core....?You will probably have to pull half your interior/dash out. See if you can find a Haynes Repair manual for the car or check ebay for a factory service manual on CD. It's most likely a bunch of trim panels and screws you have to pull off. Be careful though, you're likely to break all that old plastic when you pull it apart.Details on how to change a heater core....?its not easy but take your time.remove the glove box and you will see the heater box disconnect the power line to the blower motor and you will see the core. you will see the problem . at this point you will have scraped up fingers cause its a small place to get at. the core is about 20 dollars .bring the old core with you to match it up and maybe get a core credit. p.s get new clamps.I need to know a website to go to to find out how to change a heater core in a 93 chev cavilier?
you don't need a book its actually the easiest heater core I know of to change.Take the trim down in the center under the radio just above the hump.It's the black trim under the dash.and the heater core is right there very easy accessI need to know a website to go to to find out how to change a heater core in a 93 chev cavilier?I dont know about a website, but books are available for just about every make, model and year of car out there. I think %26quot;Paine%26quot; is one maker of such books. They may not be as good as what Mr. Goodwrench has available, but they are available at most discount auto parts stores. When you find the book, then check out ebay books, barnes and Noble used books etc. for bargains. Not the most fun job more than likely. good luck.I need to know a website to go to to find out how to change a heater core in a 93 chev cavilier?www.autozone.comI need to know a website to go to to find out how to change a heater core in a 93 chev cavilier?I don't know a website, but invest in a Chilton or Haynes manual for your car. If you do your own repairs, they are worth more than you will pay for them. Changing out a heater core in many cars is no easy task.hosting black ish powder
How to change a heater core on a 89 dodge dakota?
not much fun. remove the lower dash. evac and recharge ac. remove ac/heater plenum. take plenum apart. replace core. reinstall plenum. recharge ac.
did one on my 95! make sure that its the core and not a leaking clamp....dont ask me how i know that... :0How to change a heater core on a 89 dodge dakota?TOO MUCH TO EXPLAIN, THIS IS A VERY DIFFICULT JOB TO DO AND YOU WILL NEED SOME TYPE OF EXPERIENCE IN THE A/C FIELD AS WELL.
TRY FINDING AN INDEPENDENT SHOP INSTEAD OF THE DEALER OR A CHAIN STORE BECAUSE YOU WILL BE OVERALL MORE PLEASED WITH THE FINDINGS AND THE SERVICE.
did one on my 95! make sure that its the core and not a leaking clamp....dont ask me how i know that... :0How to change a heater core on a 89 dodge dakota?TOO MUCH TO EXPLAIN, THIS IS A VERY DIFFICULT JOB TO DO AND YOU WILL NEED SOME TYPE OF EXPERIENCE IN THE A/C FIELD AS WELL.
TRY FINDING AN INDEPENDENT SHOP INSTEAD OF THE DEALER OR A CHAIN STORE BECAUSE YOU WILL BE OVERALL MORE PLEASED WITH THE FINDINGS AND THE SERVICE.
How to change a heater core in a 1997 pontiac grand am.?
First of all....have patience.
Obtain a repair manual (NOT CHILTON) from a auto parts store and begin. It will come out from under the dash.How to change a heater core in a 1997 pontiac grand am.?visit www.mygmlink.comHow to change a heater core in a 1997 pontiac grand am.?if not ac eqiped if it has ac dash needs to come outHow to change a heater core in a 1997 pontiac grand am.?if you have to ask, better take it to someone who knows what he's doing. You could mess more up than you'd fix, if you don't do it right.
Obtain a repair manual (NOT CHILTON) from a auto parts store and begin. It will come out from under the dash.How to change a heater core in a 1997 pontiac grand am.?visit www.mygmlink.comHow to change a heater core in a 1997 pontiac grand am.?if not ac eqiped if it has ac dash needs to come outHow to change a heater core in a 1997 pontiac grand am.?if you have to ask, better take it to someone who knows what he's doing. You could mess more up than you'd fix, if you don't do it right.
How to change a heater core on a 1995 plymouth voyager?
Get a Hanes manual for this make and model car. Try your public library.How to change a heater core on a 1995 plymouth voyager?Here's the trick:
Luckily it ain't a 96...
Either way, dodge puts all the a/c and heating in a single box that is bolted to the firewall. You have to pull the whole danged box out. If it were a 96, whole danged dash comes out. On yours, only half comes out.
Disconnect battery so you don't have to worry about shorting something out or blowing out the airbags when you move the wires..
On yours, you just have to pull the heater controls, radio, and the entire knee bolster (the lower trim panel that faces your knees), including the lower center console (ash tray, misc storage, etc).
Get all the misc wiring harnesses, vacuum lines, and other BS out of the way and disconnected from the box.
Drain radiator. Disconnect the heater hoses.
Disconnect the a/c lines (pull the 13mm that secures the line to a block. Then take the two torx head screws out of the block). Then you have to pull all the nuts that secures the heater box to the firewall.
Put the box on the ground, and take it apart. About 400 screws hold it together.
Make sure when you reassemble the box all the doors move...else you get to do it again...
Reassemble.
Luckily it ain't a 96...
Either way, dodge puts all the a/c and heating in a single box that is bolted to the firewall. You have to pull the whole danged box out. If it were a 96, whole danged dash comes out. On yours, only half comes out.
Disconnect battery so you don't have to worry about shorting something out or blowing out the airbags when you move the wires..
On yours, you just have to pull the heater controls, radio, and the entire knee bolster (the lower trim panel that faces your knees), including the lower center console (ash tray, misc storage, etc).
Get all the misc wiring harnesses, vacuum lines, and other BS out of the way and disconnected from the box.
Drain radiator. Disconnect the heater hoses.
Disconnect the a/c lines (pull the 13mm that secures the line to a block. Then take the two torx head screws out of the block). Then you have to pull all the nuts that secures the heater box to the firewall.
Put the box on the ground, and take it apart. About 400 screws hold it together.
Make sure when you reassemble the box all the doors move...else you get to do it again...
Reassemble.
How to change a heater core on a 1995 chevy sonoma v6?
what iam looking for is a site that will show diagramswith step by step instructions please help find that web site that helps people work on cars and trucksHow to change a heater core on a 1995 chevy sonoma v6?you can try auto zone .com or just go there yourself and get the book on it yourself,it show's more and explain's thing's better,or you can bypass the core by taking the hoses off the core and remove one,put the other one motor to motor,you wont have heat but you can drive it till you get the new core in and put the hoses back to the core..How to change a heater core on a 1995 chevy sonoma v6?takes alot of work I would suggest you not attempt it!!How to change a heater core on a 1995 chevy sonoma v6?If you can afford it take it to someone else it will save you alot name calling and fit throwing they are a b,,,h to do unles you are a glutton for punishment do it your self. Have fun and good luck.
Subscribe to:
Posts
(Atom)